L. S. L. Elements. (C) Carbon, max. (Mn) Manganese, max. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality ASTM A Stainless Steel Rectangular Tube, ASTM A Global Steel is one of the leading manufacturers, Supplier and exporters of High Quality ASTM A Steel Pipes, ASTM A Polished Stainless Steel Pipes.

Author: Dahn Mokree
Country: Somalia
Language: English (Spanish)
Genre: Spiritual
Published (Last): 26 July 2004
Pages: 85
PDF File Size: 9.84 Mb
ePub File Size: 12.56 Mb
ISBN: 883-1-22040-798-9
Downloads: 33126
Price: Free* [*Free Regsitration Required]
Uploader: Kat

Bright Annealed, Polished Trade Name: Link to Active This link will always route to the current Active version of the standard. Permissible Variations in Cut Length in. Also see Footnote B.

Twist In 3 ft. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up z554 date. Radii of Corners, max. Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.

Where ellipses … appear in this table, there is no minimum and analysis for the element need not be determined or reported. The grades covered are listed in Table 1. B For ovality values, the tolerance for average outside diameter at any one cross section does not exceed the outside diameter tolerance value for the applicable outside diameter.

ASTM A554 304/304L/304H Stainless Steel EFW Tubes

A Grade Tube. The values given in parentheses are mathematical conversions to Atm units that are provided for information only and are not considered standard. A Grade L Tube. Click here For more ss material price list. A These tolerances apply to cut lengths up asfm and including 24 feet. Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.

Ovality is the difference between maximum and minimum outside diameters measured at any one cross section. Small outside diameter tubes are defined as those less than 0. For sizes up to and including 5-in.

ASTM A, ASTM A, ASTM A – Chicago Tube & Iron

For square or rectangular structural tubing with heavier walls, the radius of any outside corner of the section shall not exceed three times the specified wall thickness. Tolerances Hot Finished Round Table. Elongation in 2 in.

Therefore, the wall thickness can vary 15 percent aa554 and under that specified, and the inside diameter is governed by both the outside diameter and wall thickness tolerances.

E These tolerances apply to cut lengths up to and including 24 feet. Ratio of Wall Thickness to Outside Diameter. The straightness tolerance is 0.

Largest Specified Outside Dimension, Inches. Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Up to 6 meters, custom cut lengths Thickness: Tied with steel trips, then wrapped by plastic material.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Nominal Pipe Size Inches.

ASTM A Specification | Penn Stainless Products

A welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed in a number of standard sizes and grades. Small outside diameter tubes are defined as those less than 0.

Heat analysis shall be performed wherein several grades of steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, titanium, columbium, and tantalum. The average of maximum and minimum outside diameter readings should fall within the outside diameter tolerances as shown in this table. The values given in parentheses are mathematical conversions to SI zstm that are provided for information only and are not considered standard.

We can offer polished stainless steel pipes in NO. Tubes shall be furnished in one of the following shapes – round, square, rectangular, or special.